manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 297 / 346

Share
Download
Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 297

 

Alarms, faults and system messages 

 

9.3 Faults 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

295

 

Extended settings for faults 

Table 9- 8 

Advanced settings 

Parameter 

Description 

 

You can change the fault response of the motor for up to 20 different fault codes: 
p2100 

Setting the fault number for fault response 
Selecting the faults for which the fault response should be changed 

p2101 

Setting, fault response 
Setting the fault response for the selected fault 

 

You can change the acknowledgement type for up to 20 different fault codes: 
p2126 

Setting the fault number for the acknowledgement mode 
Selecting the faults for which the acknowledgement type should be changed 

p2127 

Setting, acknowledgement mode 
Setting the acknowledgement type for the selected fault 

1: Can only be acknowledged using POWER ON 

2: IMMEDIATE acknowledgment after removing the fault cause 

 

You can change up to 20 different faults into an alarm or suppress faults: 
p2118 

Setting the message number for the message type  
Selecting the message for which the message type should be selected 

p2119 

Setting the message type 
Setting the message type for the selected fault 

1: Fault 

2: Alarm 

3: No message 

You will find details in function diagram 8075 and in the parameter description of the List 

Manual. 

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Reviews:

No comments