manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 43 / 346

Share
Download
Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 43

 

Installing 

 

3.3 Installing Power Module 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

41

 

EMC-compliant installation of Power Modules in degree of protection IP20 

The EMC-compliant installation of power modules is shown in the following diagram using 

two examples. 

 

 

Example for a connection without a 

shield plate via an external filter 

Example for a connection with a shield plate, directly 

to the line supply 

①

 

Line supply connection 

②

 

Motor connection 

③

 

Metal mounting plate (unpainted and with a good electrical conductivity) 

④

 

Cable clamps for a good conductive electrical connection through a large surface area 

between the shield and mounting plate or shield plate. 

⑤

 

Shielded cable for the motor connection 

⑥

 

Shield plate 

⑦

 

Unshielded cable for connection directly to the line supply 

⑧

 

Shielded cable for connection to the line supply via an external filter. 

 

 

 

Note 
An unshielded cable for the line connection should be used for Power Modules with 

integrated filter. Power Modules, which are connected to the line supply via an external filter, 

require a shielded cable between the line filter and Power Module. 

 
 

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Reviews:

No comments