manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 258 / 346

Share
Download
Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 258

Functions 

 

7.9 Application-specific functions 

 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 

256

 

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

F30024 

Power unit: Overtemperature, thermal model 

F30025 

Power unit: Chip overtemperature 

F30027 

Power unit: Time monitoring for DC link pre-charging 

F30036 

Power unit: Overtemperature, inside area 

F30071 

No new actual values received from the Power Module 

F30072 

Setpoints can no longer be transferred to the Power Module 

F30105 

PU: Actual value sensing error 

F30662 

Internal communication error 

F30664 

Fault during power-up 

F30802 

Power unit: Time slice overflow 

F30805 

Power unit: EPROM checksum not correct 

F30809 

Power unit: Switching information invalid 

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Reviews:

No comments