Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 249

Page: 249 / 346

Functions

7.9 Application-specific functions

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

247

7.9.7

Real time clock (RTC)

The real time clock is the basis for time-dependent process controls, e.g.:
●

To reduce the temperature of a heating control during the night

●

Increase the pressure of a water supply at certain times during the day

Real time clock: Format and commissioning

The real time clock starts as soon as the Control Unit power supply is switched on for the

first time. The real time clock comprises the clock time in a 24 hour format and the date in

the "day, month, year" format.
After a Control Unit power supply interruption, the real time clock continues to run for approx.

five days.
If you wish to use the real time clock, you must set the time and date once when

commissioning. If you restore the inverter factory setting, the real time clock parameters are

not reset.

Parameter

Real time clock (RTC)

p8400[0]

RTC time, hour (0 … 23)

p8400[1]

RTC time, minute (0 … 59)

p8400[2]

RTC time, second (0 … 59)

p8401[0]

RTC date , day (1 … 31)

p8401[1]

RTC date , month (1 … 12)

p8401[2]

RTC date , year (1 … 9999)

r8404

RTC weekday
1: Monday

2: Tuesday

3: Wednesday

4: Thursday

5: Friday

6: Saturday

7: Sunday

p8405

RTC activate/deactivate alarm A01098
Sets whether the real time clock issues an alarm if the time is not running in

synchronism (e.g. after a longer power supply interruption).

0: Alarm A01098 deactivated

1: Alarm A01098 activated

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews:

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 249 / 346

Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews: