manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 85 / 346

Share
Download
Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 85

 

Commissioning 

 

4.6 Data backup and standard commissioning 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

83

 

4.6.2

 

Backing up and transferring settings using STARTER 

Backing up the inverter settings on PC/PG (upload)  

1.

 

Go online with STARTER: 

. 

2.

 

Click on the button "Load project to PG":  . 

3.

 

To save data in the PG (computer), click on  . 

Transferring settings from the PC/PG into the inverter (download)  

1.

 

Go online with STARTER. 

2.

 

Click on the button "Load project to target system":  . 

3.

 

To save data in the converter, click on "Copy RAM to ROM" 

. 

4.6.3

 

Saving settings and transferring them using an operator panel 

You start the download or upload in the "TOOLS" menu.  

4.6.4

 

Other ways to back up settings 

You can backup three additional settings of the parameters in memory areas of the inverter 

reserved for this purpose. You will find additional information in the List Manual under the 

following parameters: 

 

Parameter  Description 
p0970 

Resetting drive parameters 
Load the back-up setting (number 10, 11 or 12). You overwrite your actual parameter 

setting when loading. 

p0971 

Saving parameters 
Backing up the setting (10, 11 or 12). 

 
You can back-up up to 99 additional parameter settings on the memory card. You will find 

additional information in the List Manual under the following parameters: 

 

Parameter  Description 
p0802 

Data transfer with memory card as source/target 

p0803 

Data transfer with device memory as source/target 

p0804 

Start data transfer 

 

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Reviews:

No comments