Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 266

Page: 266 / 346

Functions

7.9 Application-specific functions

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN

264

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

Parameters to set and activate the cascade control:

p0730 = r2379.0

Signal source for digital output 0

Control external motor 1 via DO 0

p0731 = r2379.1

Signal source for digital output 1

Control external motor 2 via DO 1

p0732 = r2379.2

Signal source for digital output 2

Control external motor 3 via DO 2

p2200 = 1

Technology controller enable

Activate technology controller

p2251 = 0

Technology controller mode

Technology controller as main speed setpoint

p2370

Cascade control - enable

Signal source for staging on/off

p2371

Cascade control- configuration Activate staging and define switch-on sequence

p2372

Cascade control - motor selection mode

Define automatic motor switch-on

p2373

Cascade control - switch-in threshold

Define switch-on threshold

p2374

Cascade control - switch-in delay

Define delay time

p2375

Cascade control switch-off delay

Define delay time for destaging

p2376

Cascade control - overcontrol threshold

Define overcontrol threshold

p2377

Cascade control - interlock time

Define interlock time

p2378

Cascade control - switch-on/switch-off speed

Defining the speed for the main drive after switching-on/switching-off a motor

r2379

Cascade control - status word

p2380

Cascade control - operating hours

p2381

Cascade control - maximum time for continuous mode

p2382

Cascade control - absolute operating time limit

p2383

Cascade control - switch-off sequence

Define switch-off sequence for an OFF command

p2384

Cascade control - motor switch-on delay

Define motor switch-on delay

p2385

Cascade control - switch-in speed hold time

Define speed hold time after switching-in of an external motor

p2386

Cascade control - motor switch-off delay

Define motor switch-off delay

p2387

Cascade control - switch-off speed hold timeDefine speed hold time after

switching-off of an external motor

For more information about the parameters, see the List Manual.

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews:

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 266 / 346

Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews: