Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 208

Page: 208 / 346

Functions

7.6 Motor control

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN

206

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

7.6.1

V/f control

V/f control sets the voltage at the motor terminals on the basis of the specified speed

setpoint. The relationship between the speed setpoint and stator voltage is calculated using

characteristic curves. The required output frequency is calculated on the basis of the speed

setpoint and the number of pole pairs of the motor (f = n * number of pole pairs / 60, in

particular: f

max

= p1082 * number of pole pairs / 60). The inverter provides the two most

important characteristics (linear and square-law). User-defined characteristic curves are also

supported.
V/f control is not a high-precision method of controling the speed of the motor. The speed

setpoint and the speed of the motor shaft are always slightly different. The deviation

depends on the motor load. If the connected motor is loaded with the rated torque, the motor

speed is below the speed setpoint by the amount of the rated slip. If the load is driving the

motor (i.e. the motor is operating as a generator), the motor speed is above the speed

setpoint.
The characteristic is selected during commissioning, using p1300.

7.6.1.1

V/f control with linear and square-law characteristic

V/f control with linear characteristic (p1300 = 0):

Mainly used in applications in which the motor torque

must be independent of the motor speed. Examples of

such applications include horizontal conveyors or

compressors.

PD[

RXWSXW

PD[

V/f control with parabolic characteristic (p1300 = 2)

Used in applications in which the motor torque

increases with the motor speed Examples of such

applications include pumps and fans.
V/f control with square-law characteristic reduces the

losses in the motor and inverter due to lower currents

than when a linear characteristic is used.

PD[

RXWSXW

PD[

Note
V/f control with a square-law characteristic must not be used in applications in which a high

torque is required at low speeds.

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews:

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 208 / 346

Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews: