Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 256

Page: 256 / 346

Functions

7.9 Application-specific functions

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN

254

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

Special features of the essential service mode

●

The automatic restart function is internally activated – independent of the setting of p1210

– as soon as the essential service mode kicks in. This results in the inverter being

restarted if a pulse inhibit (OFF2) occurs due to an internal fault.

●

In the essential service mode, inverter shutdown due to faults is suppressed, with the

exception of faults that would lead to the destruction of the inverter. You will find a a list of

these faults in Section Essential service mode (Page 252).

●

The essential service mode is triggered by a continuous signal (level-triggered) using the

digital input which was defined in p3880 as the source for the essential service mode.

●

In the essential service mode, the motor can only be stopped if the line voltage is

switched off.

●

If the essential service mode is deactivated, the inverter reverts to normal operation and

its behavior depends on the pending commands and setpoints.

●

The essential service mode has priority over other operating modes

NOTICE

Loss of warranty for an inverter in the essential service mode
In the case of the essential service mode, the customer can no longer lodge any claims

for warranty. The essential service mode and the faults that arise while in the essential

service mode are logged in a password protected memory and can be read by the repair

center.

Refer to parameters p3880 … r3889 for more information on the essential service mode.

Note
Other preconditions for the essential service mode
In order to operate the inverter in the emergency service mode, the appropriate degrees of

protection and connection and installation guidelines applicable to the system should be

observed. You will find details of this in the Australian Standard: AS/NZS 1668.1:1998.

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews:

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 256 / 346

Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews: