Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 107

Page: 107 / 346

Configuring the fieldbus

6.1 Communication via PROFIBUS

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

105

6.1.4.2

Control and status word 3

The control and status words fulfill the specifications of PROFIdrive profile version 4.1 for

"speed control" mode.

Control word 3 (STW3)

Control word 3 has the following default assignment. You can change the assignment with

BICO technology.

Table 6- 8

Control word 3 and interconnection with parameters in the converter

Meaning

Bit Value

Telegram 350

Comments

BICO interconnection

0 1

Fixed setpoint, bit 0

p1020[0] = r2093.0

1 1

Fixed setpoint, bit 1

p1021[0] = r2093.1

2 1

Fixed setpoint, bit 2

p1022[0] = r2093.2

3 1

Fixed setpoint, bit 3

Selects up to 16 different fixed

setpoints.

p1023[0] = r2093.3

4 1

DDS selection, bit 0

p0820 = r2093.4

5 1

DDS selection, bit 1

Changes over between settings for

different motors (drive data sets).

p0821 = r2093.5

6 –

Not used

7 –

Not used

8 1

Technology controller enable

p2200[0] = r2093.8

9 1

DC braking enable

p1230[0] = r2093.9

10 –

Not used

11 1

1 = Enable droop

Enable or inhibit speed controller

droop.

p1492[0] = r2093.11

Torque control active

Speed control active

Changes over the control mode for

vector control.

p1501[0] = r2093.12

No external fault

External fault is active (F07860)

p2106[0] = r2093.13

14 –

Not used

15 1

CDS bit 1

Changes over between settings for

different operation interfaces

(command data sets).

p0811[0] = r2093.15

If you switch from telegram 350 to a different one, then the converter sets all interconnections p1020, … to "0".

Exception: p2106 = 1.

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews:

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 107 / 346

Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews: