manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 306 / 346

Share
Download
Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 306

Technical data 

 

10.1 Technical data for CU230P-2 

 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 

304

 

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

Feature 

Data / explanation 
PTC: Short-circuit monitoring < 20 Ω, overtemperature 1650 Ω 
KTY84: Short-circuit monitoring < 50 Ω, wire-break: > 2120 Ω 

Motor temperature sensor 

ThermoClick sensor with dry contact 

USB interface 

Mini 5-pole USB 

 

MMC card 

Recommendation: 6SL3254-0AM00-0AA0 

Memory card (optional)  

SD card 

Recommendation: 6SL3254-0AM00-0AA0 

Dimensions (WxHxD) 

73 mm × 199 mm × 65.5 mm 

Weight 

0.61 kg 

 

0 °C … 60 °C 

For operation without operator panel 

Operating temperature 

0 °C … 50 °C 

For operation with operator panel 

Storage temperature 

- 40°C … 70 °C% 

 

Relative humidity 

< 95 % 

Condensation must not be allowed to form 

V/f control for motor speeds between 0 rpm and 210000 rpm: 

•

 

Linear V/f control, 

•

 

Linear V/f control with FCC, 

•

 

Linear V/f control with ECO mode, 

•

 

Quadratic V/f control, 

•

 

Multipoint V/f control, 

•

 

V/f control for applications in the textile industry, 

•

 

V/f control with FCC for applications in the textile industry, 

•

 

V/f control with independent voltage setpoint, 

Open-loop/closed-loop 

control procedure 

Vector control for motor speeds between 0 rpm and 14400 rpm:  

•

 

Speed control without encoder 

•

 

Torque control without encoder 

The control terminals on the Control Unit are galvanically isolated from the supply voltage 

(PELV). 

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Reviews:

No comments