manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 228 / 346

Share
Download
Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 228

Functions 

 

7.9 Application-specific functions 

 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 

226

 

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

Main features of the braking functions  

 

DC braking  
The motor converts the regenerative power into 

heat. 

•

 

Advantage: The motor brakes without the 

inverter having to process the regenerative 

energy 

•

 

Disadvantages: significant increase in the 

motor temperature; no defined braking 

characteristics; no constant braking torque; no 

braking torque at standstill; regenerative 

power is lost as heat; does not function when 

the line supply fails 

Compound braking 
The motor converts the regenerative power into 

heat. 

•

 

Advantage: Defined braking characteristics, 

the motor brakes without the inverter having to 

convert any regenerative energy 

•

 

Disadvantages: significant motor temperature 

rise; no constant braking torque; regenerative 

power is dissipated as heat; does not function 

when the line supply fails 

a

 

a

 

0RWRU

%UDNH

SRZHU

/RDG

,QYHUWHU

0

 

 
Dynamic braking 
The inverter converts the regenerative 

power into heat using a braking resistor. 

•

 

Advantages: defined braking 

characteristics; no additional motor 

temperature increase; constant 

braking torque; in principle, also 

functions when the power fails 

•

 

Disadvantages: Braking resistor 

required; regenerative power is 

dissipated as heat 

a

 

a

 

,QYHUWHU

%UDNLQJUHVLVWRU

%UDNLQJUHVLVWRU

0RWRU

%UDNH

SRZHU

/RDG

,QYHUWHU

%UDNLQJ FKRSSHU

0

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Reviews:

No comments