Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 101 | Manualshive

Page: 101 / 346

Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 101

Configuring the fieldbus

6.1 Communication via PROFIBUS

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

99

6.1.2

Setting the address

You can set the inverter's PROFIBUS address using either DIP switches on the Control Unit

or parameter p0918.

Valid PROFIBUS addresses:

1 … 125

Invalid PROFIBUS addresses:

0, 126, 127

If you have specified a valid address using DIP switches, this address will always be the one

that takes effect and p0918 cannot be changed.
If you set all DIP switches to "OFF" (0) or "ON" (1), then p0918 defines the address.
The positions and settings of the DIP switches are described in Section: Interfaces,

connectors, switches, control terminals, LEDs on the CU (Page 46).

CAUTION

A bus address that has been changed is only effective after the inverter has been switched

off and back on again.

«
...
99
100
101
102
103
...
»

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Reviews:

No comments