manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 292 / 346

Share
Download
Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 292

Alarms, faults and system messages 

 

9.2 Alarms 

 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 

290

 

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

If the alarm history is filled up to index 63, each time a new alarm is accepted in the alarm 

history, the oldest alarm is deleted. 

Parameters of the alarm buffer and the alarm history 

Table 9- 5 

Important parameters for alarms 

Parameter 

Description 

r2122 

Alarm code 
Displays the numbers of alarms that have occurred 

r2123 

Alarm time received in milliseconds 
Displays the time in milliseconds when the alarm occurred 

r2124 

Alarm value 
Displays additional information about the alarm 

r2125 

Alarm time removed in milliseconds 
Displays the time in milliseconds when the alarm was removed 

p2111 

Alarm counter 
Number of alarms that have occurred after the last reset 

When setting p2111 = 0, all of the alarms that have been removed from the alarm 

buffer [0...7] are transferred into the alarm history [8...63] 

r2145 

Alarm time received in days 
Displays the time in days when the alarm occurred 

r2132 

Actual alarm code 
Displays the code of the alarm that last occurred 

r2134 

Alarm value for float values 
Displays additional information about the alarm that occurred for float values 

r2146 

Alarm time removed in days 
Displays the time in days when the alarm was removed 

Extended settings for alarms 

Table 9- 6 

Extended settings for alarms 

Parameter 

Description 

You can change up to 20 different alarms into a fault or suppress alarms: 
p2118 

Setting the message number for the message type  
Select the alarms for which the message type should be changed 

p2119 

Setting the message type 
Setting the message type for the selected alarm 

1: Fault 

2: Alarm 

3: No message 

You will find details in function block diagram 8075 and in the parameter description of the 

List Manual. 

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Reviews:

No comments