manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 87 / 346

Share
Download
Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 87

 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

85

 

Adapting the terminal strip 

5

5.1

 

Preconditions 

Before you adapt the inputs and outputs of the inverter, you should have completed the 

basic commissioning, see Chapter Commissioning (Page 53) . 
In the basic commissioning, select an assignment of the inverter interfaces from several 

predefined configurations, see Section Preparing for commissioning (Page 56).  
If none of the predefined configurations completely matches your application, then you must 

adapt the assignment of the individual inputs and outputs. You do this by changing the 

internal interconnection of an input or output using BICO technology  (Page 16).  

8

,

8

,

7(03

7(03

,

 ',
 ',
 ',
 ',

 ',
 ',




'21&
'212
'2&20

'212
'2&20

$2
*1'

*1'

r0722.0

BO: ryyxx.n

r0722.1

r0722.2
r0722.3
r0722.4

r0722.5

CO: rxxyy

p0771[0]

 $2

p0771[1]

p0731

p0730



'21&
'212
'2&20

p0732

BI: pxxxx

 $,

$,

r0755[0]

CI: pyyyy

p0756[0]

r0755[1]

p0756[1]

p0776[0]

p0776[1]

 $,

$,

 $,

*1'

r0755[2]

p0756[2]

r0755[3]

p0756[3]

 $,

*1'

 

Figure 5-1 

Internal interconnection of the inputs and outputs  

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Reviews:

No comments