Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 72

Page: 72 / 346

Commissioning

4.5 Commissioning with STARTER

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

4.5.2

Generating a STARTER project

Creating a STARTER project using project wizards

•

Using "Project / New with

wizard" create a new project.

•

To start the wizard, click on

"Search online for drive

units ...".

•

The wizard guides you through

all of the settings that you need

for your project.

4.5.3

Go online and perform the basic commissioning

Going online

•

①

Select your project and go online: .

•

In the next screen form, select the device or the

devices with which you want to go online.

If you want to go online via the USB interface, then

set the access point to "DEVICE".

•

In the next screen form, download the hardware

configuration that you found online into your project

(PG or PC).

•

STARTER shows you which converters it is accessing online and which are offline:

②

The converter is offline

③

The converter is online

•

④

If you are online, open the screen form of the Control Unit.

•

Start the wizard for the basic commissioning.

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews:

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 72 / 346

Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews: