Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 146

Page: 146 / 346

Configuring the fieldbus

6.2 Communication via RS485

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN

144

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

6.2.4.1

Setting the address

You can define the MAC ID of the inverter using DIP switches on the Control Unit or using

p2021.
Valid BACnet addressing range: 1 … 127
If you specify the address using the DIP switch, then this address is always effective and

p2021 cannot be changed.
If you want to specify the address using p2021, we recommend setting all the DIP switches

to "OFF" (0).
The positions and settings of the DIP switches are described in Section Interfaces,

connectors, switches, control terminals, LEDs on the CU (Page 46).

CAUTION

A bus address that has been changed is only effective after switching-off and switching-on

again. It is particularly important that any external 24 V supply is switched off.

6.2.4.2

Basic settings for communication

P no.

Parameter name

P0015 = 21

Macro drive unit
Selecting the I/O configuration

p2030 = 5

Fieldbus telegram selection

5: BACnet

p2020

Baud rate

6: 9600 (factory setting)

7: 19200

8: 38400

10: 76800

p2024[0 … 2]

Processing times

P2024 [0]: 0 ms … 10000 ms, maximum processing time (APDU timeout), factory

setting = 1000 ms,
P2024 [1 … 2]: No significance for BACnet

p2025[0…3]

BACnet communication parameter

•

p2025 [0]: 0 … 4194303, Device object instance number,
Factory setting = 1

•

p2025 [1]: 1 … 10, Maximum Info Frames, factory setting = 1

•

p2025 [2]: 0 … 99, Number of APDU Retries (repeated attempts after fault
telegrams), factory setting = 3

•

p2025 [3]: 1 … 127, maximum Master address, factory setting = 127

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews:

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 146 / 346

Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews: