Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 327

Page: 327 / 346

Appendix

A.1 Application examples

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

325

When you add the SIMATIC 300, a window is displayed in which you can define the network.
●

Create a PROFIBUS DP network.

Figure A-2

Inserting a SIMATIC 300 station with PROFIBUS DP network

A.1.1.4

Configuring communications to a SIMATIC control

The inverter can be connected to a SIMATIC control in two ways:
1.

Using the inverter GSD

Using the STEP 7 object manager
This somewhat more user-friendly method is only available for S7 controls and installed

Drive ES Basic (see Section Modularity of the converter system (Page 21)).

The following section describes how to configure the inverter using the GSD.

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews:

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 327 / 346

Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews: