Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 240

Page: 240 / 346

Functions

7.9 Application-specific functions

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN

238

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

Table 7- 40 Advanced settings

Parameter Description
P1201

Flying restart enable signal source (factory setting: 1)
Defines a control command, e.g. a digital input, through which the flying restart function

is enabled.

P1202

Flying restart search current (Factory setting for Power Module PM230: 90 %. Factory

setting for PM240, PM250 and PM260: 100%)
Defines the search current with respect to the motor magnetizing current (r0331), which

flows in the motor while the flying restart function is being used.

P1203

Flying restart search speed factor (Factory setting for Power Module PM230: 150 %.

Factory setting for PM240, PM250 and PM260: 100%)
The value influences the speed with which the output frequency is changed during the

flying restart. A higher value results in a longer search time.
If the inverter does not find the motor, reduce the search speed (increase p1203).

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews:

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 240 / 346

Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews: