manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 294 / 346

Share
Download
Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 294

Alarms, faults and system messages 

 

9.3 Faults 

 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 

292

 

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

The fault buffer can accept up to eight actual faults. The next to last fault is overwritten if an 

additional fault occurs after the eighth fault. 

VWIDXOW

QGIDXOW

UGIDXOW

WKIDXOW

WKIDXOW

WKIDXOW

WKIDXOW

/DVWIDXOW

)DXOWFRGH

)DXOWYDOXH

)DXOWWLPH

UHFHLYHG

)DXOWWLPH

UHPRYHG

U>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

>@

U>@ U>@

U>@

U>@

U>@

U>@

 

Figure 9-7 

Complete fault buffer 

Fault acknowledgement 

In most cases, you have the following options to acknowledge a fault:  
●

 

Switch-off the inverter power supply and switch-on again. 

●

 

Press the acknowledgement button on the operator panel 

●

 

Acknowledgement signal at digital input 2 

●

 

Acknowledgement signal in bit 7 of control word 1 (r0054) for Control Units with fieldbus 

interface 

Faults that are triggered by monitoring of hardware and firmware inside the inverter can only 

be acknowledged by switching off and on again. You will find a note about this restricted 

option to acknowledge faults in the fault list of the List Manual. 

Emptying the fault buffer: Fault history  

The fault history can contain up to 56 faults. 
The fault acknowledgement has no effect as long as none of the fault causes of the fault 

buffer have been removed. If at least one of the faults in the fault buffer has been removed 

(the cause of the fault has been removed) and you acknowledge the faults, then the 

following happens: 
1.

 

The inverter accepts all faults from the fault buffer in the first eight memory locations of 

the fault history (indices 8 ... 15). 

2.

 

The inverter deletes the faults that have been removed from the fault buffer. 

3.

 

The inverter writes the time of acknowledgement of the faults that have been removed 

into parameters r2136 and r2109 (fault time removed). 

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Reviews:

No comments