manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 271 / 346

Share
Download
Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 271

 

Functions 

 

7.9 Application-specific functions 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

269

 

7.9.14

 

Energy-saving mode 

The energy-saving mode is mainly used for pumps and fans. Typical applications include 

pressure and temperature controls. 
In the energy-saving mode, the inverter stops and starts the motor depending on the system 

conditions. The energy-saving mode can be activated via the technology controller (without 

external commands via terminals or bus interface) and via an external setpoint input. 
The energy-saving mode offers the advantages of energy saving, lowering mechanical wear 

and reduced noise. 

 

 

Note 
In the energy-saving mode, if the setpoint is to be entered from the motorized potentiometer 

or from the motorized potentiometer of the technology controller, you must set p1030.4 or 

p2230.4 = 1. 

 

NOTICE 

 

After the inverter has been powered up, the motor goes into the energy-saving mode if the 

energy-saving mode start speed has still not been reached after the highest value from 

p1120 (ramp-up time), p2391 (energy-saving mode delay time) and 20 s have expired. 

 

Operating principle 

The energy-saving mode starts as soon as the motor speed drops below the energy-saving 

mode start speed. However, the motor is only switched off after an adjustable time has 

expired. If, during this time, the speed setpoint increases above the energy-saving mode 

start speed due to pressure or temperature changes, the energy-saving mode is exited and 

the inverter goes into normal operation.  

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Reviews:

No comments