Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 308

Page: 308 / 346

Technical data

10.2 Technical data, Power Modules

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN

306

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

Definitions

•

LO input current

100 % of the permissible input current for a load cycle according to

Low Overload (LO base load input current).

•

LO output current

100 % of the permissible output current for a load cycle according

to Low Overload (LO base load output current).

•

LO power

Power of the inverter for LO output current.

•

HO input current

100 % of the permissible input current for a load cycle according to

High Overload (HO base load input current).

•

HO output current

100 % of the permissible output current for a load cycle according

to High Overload (HO base load output current).

•

HO power

Power of the inverter for HO output current.

If the power data comprise rated values without any further specifications they always refer

to an overload capability corresponding to Low Overload.

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews:

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 308 / 346

Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews: