Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 309

Page: 309 / 346

Technical data

10.2 Technical data, Power Modules

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

307

10.2.1

Technical data, PM230

General data, PM230 - IP55 / UL Type 12

Feature

Version

Line voltage

3-ph. 380 V … 480 V AC ± 10 %

The actual permissible line voltage depends on the installation altitude

Input frequency

47 Hz … 63 Hz

Power factor λ

0.9

Starting current

Smaller than the input current

Permissible short-circuit

current

Frame size A ... C: 42 kA

Frame size D ... F: 65 kA

Pulse frequency (factory

setting)

4 kHz
The pulse frequency can be increased up to 16 kHz in 2 kHz steps. A higher pulse

frequency reduces the permissible output current.

Electromagnetic compatibility

The devices are suitable for environmental classes C1 and C2 in conformance with

IEC 61800-3. For details, see the Hardware Installation Manual, Appendix A2

Braking methods

DC braking

Degree of protection

IP55 / UL Type 12
Degree of protection IP54/ UL Type 12 is reached if an IOP is inserted.

Operating temperature

● without power reduction

● with power reduction

0 °C … +40 °C (32 °F … 104 °F)

to 60° C (140° F)

Storage temperature

-40 °C … +70 °C (-40 °F … 158 °F)

Relative humidity

< 95 % RH - condensation not permissible

Contamination

Protected from contact with dangerous parts, dust, spray water and water jets

Environmental requirements

Protected according to environmental class 3C2 to EN 60721-3-3 against damaging

chemical substances

Shock and vibration

Do not allow the inverter to fall and avoid it being subject to hard shocks. Do not install

the inverter in an area where it could be continuously subject to vibration.

Electromagnetic radiation

Do not install the inverter close to sources of electromagnetic radiation.

Installation altitude

● without power reduction

● with power reduction

Up to 1000 m (3300 ft) above sea level

up to 4000 m (13000 ft) above sea level, for details see the Hardware Installation Manual.

Standards

, CE, C-tick

In order that the system is UL-compliant, UL-certified fuses, overload circuit-breakers or

intrinsically safe motor protection devices must be used.

UL available soon for frame sizes D … F

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews:

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 309 / 346

Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews: