Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 303

Page: 303 / 346

Alarms, faults and system messages

9.4 List of alarms and faults

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

301

Number Cause

Remedy

F30005

I2t converter overload

Check the rated currents of the motor and Power Module.
Reduce current limit p0640.
When operating with U/f characteristic: Reduce p1341.

F30011

Line phase failure

Check the converter's input fuses.
Check the motor cables.

F30015

Motor cable phase failure

Check the motor cables.
Increase the ramp-up or ramp-down time (p1120).

F30021

Ground fault

•

Check the power cable connections.

•

Check the motor.

•

Check the current transformer.

•

Check the cables and contacts of the brake connection (a wire might
be broken).

F30027

Time monitoring for DC link pre-

charging

Check the supply voltage at the input terminals.
Check the line voltage setting (p0210).

F30035

Overtemperature, intake air

F30036

Overtemperature, inside area

•

Check whether the fan is running.

•

Check the fan filter elements.

•

Check whether the ambient temperature is in the permissible range.

F30037

Rectifier overtemperature

See F30035 and, in addition:

•

Check the motor load.

•

Check the line phases

A30049

Internal fan defective

Check the internal fan and if required replace.

A30502

DC link overvoltage

•

Check the unit supply voltage (p0210).

•

Check the dimensioning of the line reactor.

A30920

Temperature sensor fault

Check that the sensor is connected correctly.

F30059

Internal fan defective

Check the internal fan and if required replace.

For further information, please refer to the List Manual.

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews:

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 303 / 346

Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews: