Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 276

Page: 276 / 346

Functions

7.9 Application-specific functions

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN

274

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

Parameter

Description

Via tech.

setpoint

Via external

setpoint

P2393 = …

Energy-saving mode restart speed (rpm),

required in the case of external setpoint input. The motor starts as soon as the

setpoint exceeds the restart speed. The restart speed is calculated as follows:

Restart speed = P1080 + p2390 + p2393

P1080 = minimum speed

p2390 = energy-saving mode start speed

p2393 = energy-saving mode restart speed

P2394 = …

Energy-saving mode boost duration

0 (factory setting) … 3599 s. Before the inverter switches over into the energy-

saving mode, the motor is accelerated for the time set in p2394 according to

the acceleration ramp, but not to more than the speed set in P2395.

P2395 = …

Energy-saving mode boost speed

0 (factory setting) … 21000 rpm. Before the inverter switches over into the

energy-saving mode, the motor is accelerated for the time set in p2394

according to the acceleration ramp, but not to more than the speed set in

P2395.
Caution:

Make sure that the boost cannot cause any overpressure or overflow

conditions.

P2396 = …

Maximum energy-saving mode shutdown time

0 (factory setting) … 863999 s. At the latest when this time expires, the

inverter switches to normal operation and is accelerated up to the start speed

(P1080 + P2390). If the inverter is switched to normal operation in advance,

the shutdown time is reset to the value set in this parameter.

With p2396 = 0, automatic changeover to normal operation after a certain time

is deactivated.

Display parameters

Parameter Description
r2273

Display of the setpoint/actual value deviation of the technology controller

r2397

Actual energy-saving mode output speed

Actual boost speed before the pulses are inhibited or the actual start speed after restart.

r2399

Energy-saving mode status word

00 Energy-saving mode enabled (P2398 <> 0)

01 Energy-saving mode active

02 Energy-saving mode delay time active

03 Energy-saving mode boost active

04 Energy-saving mode motor switched off

05 Energy-saving mode motor switched off, cyclic restart active

06 Energy-saving mode motor restarts

07 Energy-saving mode supplies the total setpoint of the ramp-function generator

08 Energy-saving mode bypasses the ramp-function generator in the setpoint channel

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews:

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 276 / 346

Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews: