manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 160 / 346

Share
Download
Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 160

Configuring the fieldbus 

 

6.3 Communication over CANopen 

 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 

158

 

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

SDO abort codes 

Table 6- 45  SDO abort codes 

Abort code 

Description 

0503 0000h   Toggle bit not alternated. 

Toggle bit has not changed 

0504 0000h 

SDO protocol timed out. 
Timeout for SDO protocol 

0504 0001h 

Client/server command specifier not valid or unknown. 
Client/server command not valid or unknown 

0504 0005h 

Out of memory. 
Memory overflow 

0601 0000h 

Unsupported access to an object. 
Access to an object that is not supported 

0601 0001h 

Attempt to read a write only object. 
An attempt is made to read a "write-only object" 

0601 0002h 

Attempt to write a read only object. 
An attempt is made to write to a "read-only object" 

0602 0000h 

Object does not exist in the object dictionary. 
Object does not exist in an object dictionary 

0604 0041h 

Object cannot be mapped to the PDO. 
Object cannot be linked with the PDO 

0604 0042h 

The number and length of the objects to be mapped would exceed PDO length. 
The number and length of the objects that are to be linked exceeds the PDO length 

0604 0043h 

General parameter incompatibility reason. 
Basic parameter incompatibility 

0604 0047h 

General internal incompatibility in the device. 
Basic incompatibility in the device 

0602 0000h 

Object does not exist in the object dictionary. 
Object does not exist in an object dictionary  

0604 0041h 

Object cannot be mapped to the PDO. 
Object cannot be linked with the PDO 

0604 0042h 

The number and length of the objects to be mapped would exceed PDO length. 
The number and length of the objects that are to be linked exceeds the PDO length 

0604 0043h 

General parameter incompatibility reason.  
Basic parameter incompatibility 

0604 0047h 

General internal incompatibility in the device.  
Basic incompatibility in the device 

0606 0000h 

Access failed due to an hardware error. 
Access has failed due to a hardware fault 

0607 0010h 

Data type does not match, length of service parameter does not match. 
Data type and length of the service parameter do not match 

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Reviews:

No comments