Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 245

Page: 245 / 346

Functions

7.9 Application-specific functions

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD

243

7.9.4

PID technology controller

The technology controller permits all types of simple process controls to be implemented.

You can use the technology controller for e.g. pressure controllers, level controls or flow

controls.

3XPS

&ORVHGORRS

VSHHG

FRQWURO

/HYHO
VHQVRU

7HFKQRORJ\DFWXDOYDOXH

5DPSIXQFWLRQ

JHQHUDWRU

6HWSRLQW
WHFKQRORJ\

3,'FRQWUROOHU

6SHHG
VHWSRLQW

Figure 7-18 Example: technology controller as a level controller

Principle of operation

The technology controller specifies the speed setpoint of the motor in such a way that the

process variable to be controlled corresponds to its setpoint. The technology controller is

designed as a PID controller, which makes it highly flexible.
The technology controller setpoint is entered via an analog input or via the fieldbus.

Table 7- 42 Technology controller parameters

Parameter

Description

P2200 = …

Enable technology controller

P2201 … r2225

Fixed speeds for the technology controller

P2231 … P2248

Motorized potentiometer for the technology controller

P2251 … r2294

General adjustment parameters of the technology controller

P2345 = …

Changing the fault reaction for the technology controller

Additional information about this function is provided in the parameter list and in the function

diagrams 7950 … 7958 in the List Manual.

Additional technology controllers

Via the parameter ranges
●

p11000 … p11099: free technology controller 0

●

p11100 … p11199: free technology controller 1

●

p11200 … p11299: free technology controller 2

additional technology controllers can be parameterized. Refer to the parameter descriptions

and in function diagram 7970 of the associated List Manual for additional details.

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews:

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 245 / 346

Search results

Summary of Contents for SINAMICS G120 CU230P-2

Reviews: