manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 248 / 346

Share
Download
Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 248

Functions 

 

7.9 Application-specific functions 

 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 

246

 

Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

7.9.6

 

Load failure monitoring via digital input 

Using this function, the inverter monitors the load failure of the driven machine, e.g. for fans 

or conveyor belts.  

WRVLJQDOHYDOXDWLRQ

S

U[

39

',[

 

Figure 7-19  Load failure monitoring by means of a digital input 

Table 7- 44  Setting load failure monitoring  

Parameter  

Description 

p2193 = 1 … 3  Load monitoring configuration  (factory setting: 1) 

1: Torque and load failure monitoring 

2: Speed and load failure monitoring  

3: Load failure monitoring 

p2192 

Load monitoring delay time (factory setting 10 s) 

If, after the motor is switched on, the "LOW" signal is present on the associated 

digital input for longer than this time, a load failure is assumed (F07936) 

p3232 = 722.x  Load monitoring failure detection (factory setting: 1) 

Interconnect the load monitoring with a digital input of your choice. 

For more information, see the List Manual (the parameter list and function diagram 8013). 

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Reviews:

No comments