manualshive.com logo in svg

Siemens SINAMICS G120 CU230P-2, Operating Instructions Manual, Page: 251 / 346

Share
Download
Siemens SINAMICS G120 CU230P-2 Operating Instructions Manual Download Page 251

 

Functions 

 

7.9 Application-specific functions 

Frequency inverters with Control Units CU230P-2 HVAC, CU230P-2 DP, CU230P-2 CAN 
Operating Instructions, 01/2011, FW 4.4, A5E02430659B AD 

249

 

7.9.8

 

Time switch (DTC) 

The "time switch" (DTC) function, along with the real time clock in the inverter, offers the 

option of controlling when signals are switched on and off. 

Examples: 
●

 

Day/night switching of a temperature control 

●

 

Switching a process control from weekday to weekend. 

Principle of operation of the time switch (DTC)  

The inverter has three independent parameterizable time switches. Using BICO technology, 

the time switch output can be interconnected with every binector of your inverter, e.g. a 

digital output or a technology controller's enable signal. 

'7&RXWSXW
U

W

0RQGD\

7XHVGD\

:HGQHVGD\

7KXUVGD\

W

'HDFWLYDWHG

$FWLYDWHG

$FWLYDWHG

'HDFWLYDWHG

'7&ZHHNGD\
DFWLYDWLRQ

'7&VZLWFKLQJWLPHV

21

2))

 

 

 

 

57&
SS
U

S>@  S>@
S>@  S>@ 

S>@

S>@

S>@

S>@

 

Figure 7-20  Time behavior of the time switch using example DTC1 

Parameterizing the time switch 
●

 

Enable parameterization of the DTC: p8409 = 0.  

As long as DTC parameterization is enabled, the inverter keeps the output of all three 

DTC (r84x3, x = 1, 2, 3) on LOW. 

●

 

Parameterize the activation of the weekdays; the switching on and off times. 

●

 

Enable the setting: p8409 = 1.  

The inverter enables the DTC outputs once more. 

Additional information is provided in the parameter list of the List Manual. 

Summary of Contents for SINAMICS G120 CU230P-2



























































































































































































































































































































































Reviews:

No comments