Siemens SICAM Q100 7KG95 Series Manual Download Page 264

Page: 264 / 448

9 Operation at Use of a PC

9.3 Configuration of the Device

264

SICAM Q100, 7KG95xx, Device Manual

E50417-H1040-C522-A6, Edition 06.2019

Parameterizing the Syslog

To change the settings of the Syslog, proceed as follows:

✧

In the navigation window, select the

Administrative

menu and click

Syslog

Figure 9-83

Configure Tab, Syslog Input/Output Window

✧

In the

Parameter

fields, enter the desired values according to Table 9-42.

✧

After the parameterization click

Send

After clicking

Send

, the parameters are transmitted to the device but not enabled yet (passive set of

parameters).

✧

If you do not want to make any additional settings, continue with the

Activation

of the device configuration

according to section

Activating the Set of Parameters

. If you want to change other settings, enter the

changes and then enable the device configuration as described in section

Activating the Set of

Parameters

MAN_SICAM_Q100_US.book Page 264 Wednesday, June 5, 2019 9:31 AM

Summary of Contents for SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews:

Siemens SICAM Q100 7KG95 Series, Manual, Page: 264 / 448

Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews: