manualshive.com logo in svg

Siemens SICAM Q100 7KG95 Series, Manual, Page: 329 / 448

Share
Download
Siemens SICAM Q100 7KG95 Series Manual Download Page 329

9 Operation at Use of a PC

9.7 Example of a Parameterization and Measured Value Evaluation

329

SICAM Q100, 7KG95xx, Device Manual
E50417-H1040-C522-A6, Edition 06.2019

9.7.3

Parameterization as Defined by the Task

Requirements

SICAM Q100 is electrically connected to the system and commissioned as described in chapter 7.7. Rated 
voltages and currents at the measuring inputs are switched off.

Parameterization

✧

Start the user interface as described in chapter 9.2.1 (initial startup) or chapter 9.2.7 (start during 
operation). Use the factory-preset IP address for this purpose.

✧

On the 

Configure

 tab, configure the element 

AC measurement

 (see chapter 9.3.3.1.1) according to the 

following topology specifications:

Figure 9-142

Configure Tab, AC Measurement Example

NOTE

If you change settings in tabs, click 

Send

 on each tab to confirm the new setting. The settings are 

activated

 

only after the entire parameterization has been completed.

NOTE

If you are using Ethernet communication with 

IEC 61850 bus protocol

 (chapter 9.3.7.2) and change the 

Network type

, the device will restart.

MAN_SICAM_Q100_US.book  Page 329  Wednesday, June 5, 2019  9:31 AM

Summary of Contents for SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Reviews:

No comments