manualshive.com logo in svg

Siemens SICAM Q100 7KG95 Series, Manual, Page: 324 / 448

Share
Download
Siemens SICAM Q100 7KG95 Series Manual Download Page 324

9 Operation at Use of a PC

9.5 Maintenance

324

SICAM Q100, 7KG95xx, Device Manual

E50417-H1040-C522-A6, Edition 06.2019

Connection Statistics

The 

Connection statistics

 section shows the number of sent and received messages that can be additionally 

used for communication-status analysis.

Certificates Information

The 

Certificates information

 section shows the identification and the effective dates for each of the loaded 

certificates.

Connected to the broker, 
publishing data

-

Connection is established and data is sent to 
the broker.

Disconnected from the broker, 
trying to reconnect

-

Connection to the broker is interrupted. The 
device tries to reconnect to the broker.

Connection time-out
Connection error

Connection error
Check the communication line and firewall 
settings or whether the broker is online.

Table 9-52

Status Type

Status or Error

Additional Information

Description and Solution

Table 9-53

Connection Statistics

Statistic Counter

Description

MQTT

Connect

Times that the device connects to the broker

Sent messages

The number of sent messages on MQTT level to the broker

Disconnect

Times that the device disconnects to the broker

OPC UA PubSub

Key frames

The number of sent key frames

Meta frames

The number of sent meta frames

Keep alive

The number of sent keep-alive messages

File transfer Ok/Err

The number of successful or unsuccessful sent files

Delta frames sum

The sum number of sent delta frames

Delta frams per s

The number of delta frames sent in last second

MAN_SICAM_Q100_US.book  Page 324  Wednesday, June 5, 2019  9:31 AM

Summary of Contents for SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Reviews:

No comments