Siemens SICAM Q100 7KG95 Series Manual Download Page 154

Page: 154 / 448

9 Operation at Use of a PC

9.3 Configuration of the Device

154

SICAM Q100, 7KG95xx, Device Manual

E50417-H1040-C522-A6, Edition 06.2019

9.3.1.1 Get Device Configuration

If you have selected

Get device configuration

in the

Configure

tab, you can open and edit either the

Get

active configuration

or the

Get default configuration

in the input/output window. Proceed as follows:

Figure 9-15

Configure Tab, Get Device Configuration

Get Active Configuration and Editing

✧

Click

Get active configuration

A copy of the active set of parameters (= passive set of parameters) of the device is opened for editing.

✧

Check and, if necessary, change the set parameters by opening the desired menus in the navigation
window:

✧

Operational parameters

menu according to chapter 9.3.3

✧

HMI

settings according to chapter 9.3.4

✧

Recording and reporting

according to chapter 9.3.5.3

✧

Administrative

menu according to chapter 9.3.7.

✧

Activate the modified configuration as described in chapter 9.3.1.3.

MAN_SICAM_Q100_US.book Page 154 Wednesday, June 5, 2019 9:31 AM

Summary of Contents for SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews:

Siemens SICAM Q100 7KG95 Series, Manual, Page: 154 / 448

Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews: