Siemens SICAM Q100 7KG95 Series Manual Download Page 288

Page: 288 / 448

9 Operation at Use of a PC

9.4 Value View and Evaluation

288

SICAM Q100, 7KG95xx, Device Manual

E50417-H1040-C522-A6, Edition 06.2019

To change the

File transfer

, proceed as follows:

✧

In the navigation window, select the

Evaluation and data management

menu and click

File transfer

The

File transfer

input/output window opens.

Figure 9-102

Value View and Evaluation Tab, File Transfer Input/Output Window

✧

Select the respective parameters in the list boxes according to Table 9-49.

Option: Single file download

✧

Click

Download

The

File download

dialog opens.

✧

Click

Save

✧

Select a directory in the

Save

dialog and click on

Save

✧

To open or save the recording list, proceed as described in

chapter 9.2.7.2

NOTE

The button

Download

only is displayed if a

Record list

is available.

MAN_SICAM_Q100_US.book Page 288 Wednesday, June 5, 2019 9:31 AM

Summary of Contents for SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews:

Siemens SICAM Q100 7KG95 Series, Manual, Page: 288 / 448

Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews: