Siemens SICAM Q100 7KG95 Series Manual Download Page 102

Page: 102 / 448

6 Security

6.2 Account Management

102

SICAM Q100, 7KG95xx, Device Manual

E50417-H1040-C522-A6, Edition 06.2019

x represents that the user with this role is assigned with related rights.

✧

Enter the user name, the password, and select a role or several roles for a user account.

✧

Click

Confirm

. A user account is created.

Editing or Deleting an Existing User Account

Figure 6-6

Editing or Deleting a User Account

To edit an existing user account, proceed as follows:

✧

In the navigation window, select

Administrative

and click

Account management

✧

Click the

icon to edit the password or edit the role of an existing user account.

Figure 6-7

Editing a User Account

MAN_SICAM_Q100_US.book Page 102 Wednesday, June 5, 2019 9:31 AM

Summary of Contents for SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews:

Siemens SICAM Q100 7KG95 Series, Manual, Page: 102 / 448

Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews: