Siemens SICAM Q100 7KG95 Series Manual Download Page 214

Page: 214 / 448

9 Operation at Use of a PC

9.3 Configuration of the Device

214

SICAM Q100, 7KG95xx, Device Manual

E50417-H1040-C522-A6, Edition 06.2019

Parameterizing the Time Synchronization

To change the time synchronization, proceed as follows:

✧

In the navigation window, select the

Administrative

menu and click

Time synchronization

Figure 9-56

Configure Tab, Time Synchronization Input/Output Window, Ethernet NTP Selected

✧

Enter the desired values in the fields and select the parameters in the list boxes and in the option field as
described in Table 9-23.

✧

After the parameterization click

Send

The parameters are transmitted to the device but not enabled yet (passive set of parameters).

✧

If you do not want to make any additional settings, continue with the

Activation

of the device configuration

according to section

Activating the Set of Parameters

. If you want to change other settings, enter the

changes and then enable the device configuration as described in section

Activating the Set of

Parameters

Secondary NTP server IP address

192.168.0.253

Any
No polling of the NTP server if
0.0.0.0 was entered

Error indication after

10 min

2 min to 120 min

Additional Parameter if the Source is Fieldbus (Modbus RTU and IEC 60870-5-103)

Error indication after

10 min

2 min to 120 min

Table 9-23

Time Synchronization Settings (cont.)

Parameter

Default Setting

Setting Range

MAN_SICAM_Q100_US.book Page 214 Wednesday, June 5, 2019 9:31 AM

Summary of Contents for SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews:

Siemens SICAM Q100 7KG95 Series, Manual, Page: 214 / 448

Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews: