Siemens SICAM Q100 7KG95 Series Manual Download Page 419

Page: 419 / 448

16 Operating Parameters

16.6 Administrative

419

SICAM Q100, 7KG95xx, Device Manual
E50417-H1040-C522-A6, Edition 06.2019

16.6

Administrative

The following administrative settings are available:

•

Time synchronization

•

Communication Ethernet

•

OPC UA PubSub (MQTT)

•

Communication serial

•

Modbus slave devices 1 to 8

•

SICAM subdevices

•

Device and language

•

Account Management

•

Syslog

16.6.1

Time Synchronization

Parameter

Default Settings

Setting Range

Source time synchronization

Internal

Internal
Ethernet NTP
Fieldbus

Time zone offset

+00:00

-12 to +13 (hours)
(in increments of 0.5 h)

Daylight Saving Time switchover

yes

no
yes

DST offset

+01:00

0 to + 2 (hours)
(in increments of 0.5 h)

Start of DST

March
Last week

Sunday
02:00 AM

January to December
First week
Second week
Third week
Fourth week
Last week
Sunday to Saturday
0:00 to 23:00 (full hour)

End of DST

October
Last week

Sunday
03:00 AM

January to December
First week
Second week
Third week
Fourth week
Last week
Sunday to Saturday
0:00 to 23:00 (full hour)

Additional Parameters if the Source is Ethernet NTP (Modbus TCP and IEC 61850)

Primary NTP server IP Address

192.168.0.254

Any

Secondary NTP server IP Address

192.168.0.253

Any
No polling of the NTP server if 0.0.0.0
was entered

MAN_SICAM_Q100_US.book Page 419 Wednesday, June 5, 2019 9:31 AM

Summary of Contents for SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews:

Siemens SICAM Q100 7KG95 Series, Manual, Page: 419 / 448

Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews: