Siemens SICAM Q100 7KG95 Series Manual Download Page 411

Page: 411 / 448

16 Operating Parameters

16.4 Energy Management

411

SICAM Q100, 7KG95xx, Device Manual
E50417-H1040-C522-A6, Edition 06.2019

In this case, the protocol Modbus TCP can control tariff 1 to tariff 8. Refer to the System Manual SICAM

Q100, chapter 2.2.7.18 Register 0154: Tariffs (read and write), order number E50417-C1040-C522.

This synchronization source can only control tariff 1 or tariff 2.

The default settings of Tariff 1 Period 1 Active for 2 seasons are checked.

16.4.3

Energy Upper Limit

16.4.4

Energy Freeze and Record

Season x (x = 1 or 2) Tariff
y (y = 1 to 8) Period 1 Active

Yes
No

Season x (x = 1 or 2) Tariff
y (y = 1 to 8) Period 2 Active

Yes
No

Season x (x = 1 or 2) Tariff
y (y = 1 to 8) Workday/
Weekend Selection

Every Day

Every Day
Workday
Weekend

Coverage Check

Pass

Fail (with gap)

Fail (with overlap)

Parameter

Default Setting

Setting Range

Energy Upper Limit

Energy Counter

Energy Counter
Energy Value

Parameter

Default Setting

Setting Range

Interval

10 minutes

10 minutes
15 minutes
30 minutes
60 minutes

MAN_SICAM_Q100_US.book Page 411 Wednesday, June 5, 2019 9:31 AM

Summary of Contents for SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews:

Siemens SICAM Q100 7KG95 Series, Manual, Page: 411 / 448

Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews: