Siemens SICAM Q100 7KG95 Series Manual Download Page 261

Page: 261 / 448

9 Operation at Use of a PC

9.3 Configuration of the Device

261

SICAM Q100, 7KG95xx, Device Manual
E50417-H1040-C522-A6, Edition 06.2019

To change the settings of device and language, proceed as follows:

✧

In the navigation window, select the

Administrative

menu and click

Device and language

Figure 9-82

Configure Tab, Device and Language Input/Output Window

✧

Select the desired parameters in the list box according to Table 9-41.

✧

Change the passwords if necessary.

✧

If necessary, change the user language (see below).

✧

After the parameterization click

Send

After clicking

Send

, the parameters are transmitted to the device but not enabled yet (passive set of

parameters).

✧

If you do not want to make any additional settings, continue with the

Activation

of the device configuration

according to section

Activating the Set of Parameters

. If you want to change other settings, enter the

changes and then enable the device configuration as described in section

Activating the Set of

Parameters

Changing the User Language Preselection

The user language can be preset, for example when starting the User Interface for the first time (see chapter
9.2.1). DEUTSCH is set by default.

To change the user language, proceed as follows:

✧

Select the user language of the User Interface in the

User language preselection

list box.

✧

Click the

Send

button.

The message "User language was changed, automatic restart shall take place after Activation!" is
displayed in red on the status bar.

NOTE

If you change the user language, the device will restart after pressing the

Send

button and subsequently acti-

vating the settings.

MAN_SICAM_Q100_US.book Page 261 Wednesday, June 5, 2019 9:31 AM

Summary of Contents for SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews:

Siemens SICAM Q100 7KG95 Series, Manual, Page: 261 / 448

Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews: