manualshive.com logo in svg

Siemens SICAM Q100 7KG95 Series, Manual, Page: 157 / 448

Share
Download
Siemens SICAM Q100 7KG95 Series Manual Download Page 157

9 Operation at Use of a PC

9.3 Configuration of the Device

157

SICAM Q100, 7KG95xx, Device Manual
E50417-H1040-C522-A6, Edition 06.2019

9.3.1.3 Finish Configuration

When you have changed the configuration, you must either enable it as the active set of parameters or save it. 

Activating the Set of Parameters

To 

activate

 the set of parameters, proceed as follows:

✧

In the navigation window, select the 

Finish configuration

 menu and click 

Activation

.

Figure 9-18

Configure Tab, Activation Input/Output Window

✧

Click 

Activation

.

At first the message 

Parameter activation is still in progress

 will be shown and then the message 

Parameter activation is complete

 in the input/output window.

 

The modified set of parameters is loaded as the active set of parameters into the device and the new 
parameters take effect immediately.

Save Configuration to File

You can save both the active and the passive configuration to a file. Proceed as follows:

NOTE

The active and passive set of parameters are listed in the 

Activation

 input/output window in the 

Set

 column 

for your information.

NOTE

During the parameter activation, the device is working under special mode. If one kind of recorders happens in 
this duration, the integrity of the recorded data cannot be guaranteed.

MAN_SICAM_Q100_US.book  Page 157  Wednesday, June 5, 2019  9:31 AM

Summary of Contents for SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Reviews:

No comments