Siemens SICAM Q100 7KG95 Series Manual Download Page 322

Page: 322 / 448

9 Operation at Use of a PC

9.5 Maintenance

322

SICAM Q100, 7KG95xx, Device Manual

E50417-H1040-C522-A6, Edition 06.2019

9.5.6.4 OPC UA PubSub (MQTT)

✧

In the navigation window, select the

Diagnosis

menu and click

OPC UA PubSub (MQTT)

The

OPC UA PubSub (MQTT)

input/output window opens. The diagnostic data of OPC UA PubSub

(MQTT) is then analyzed.

Figure 9-137

Maintenance Tab, Diagnosis OPC UA PubSub (MQTT) Input/Output Window

Broker and Network

The

Broker and network

section shows the following information:

NOTE

The diagnostic data of

OPC UA PubSub (MQTT)

is displayed only if you have activated

OPC UA PubSub

(MQTT)

Configure



Administrative



Communication Ethernet

If you have not activated

OPC UA PubSub (MQTT)

, the option

OPC UA PubSub (MQTT)

is invisible under

Diagnosis

in the navigation window.

Table 9-51

Information in the Broker and Network Section

Parameter

Information

Broker IP address or host name

Configured

Topic name

Configured

MAN_SICAM_Q100_US.book Page 322 Wednesday, June 5, 2019 9:31 AM

Summary of Contents for SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews:

Siemens SICAM Q100 7KG95 Series, Manual, Page: 322 / 448

Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews: