Siemens SICAM Q100 7KG95 Series, Manual, Page: 222 / 448

Share

Page: 222 / 448

Siemens SICAM Q100 7KG95 Series Manual Download Page 222

9 Operation at Use of a PC

9.3 Configuration of the Device

222

SICAM Q100, 7KG95xx, Device Manual

E50417-H1040-C522-A6, Edition 06.2019

9.3.7.3 OPC UA PubSub (MQTT)

Function Description

The OPC UA PubSub (MQTT) protocol is used to:

•

Provide users a flexible and mobile access to the data of protection, power quality, and control devices

•

Evaluate the data of protection, power quality, and control devices

The protocol is resolved in the following ways:

•

Devices send data from different locations where data is built and stored to cloud services via an Internet
connection.

•

You retrieve the grid diagnostic data via Internet in local control centers.

•

You use mobile applications for energy management, supervision, alert detection, and maintenance
tasks.

This entire data flow of device interconnectivity (using standardized communication protocols), data access,
and data evaluation via Internet is also called IoT (Internet of Things). The basic cloud services are supplied
by a cloud-service provider, for example, Siemens MindSphere.

Configuration via User Interface

To change the settings of the protocol in the

Configure

tab, proceed as follows:

✧

Activate the

Protocol OPC UA PubSub (MQTT)

protocol by selecting

yes

in

Configure

->

Administrative

->

Communication

->

Protocol OPC UA PubSub (MQTT)

.

NOTE

The protocol OPC UA PubSub (MQTT) is available in the firmware of SICAM Q100 V2.10 or higher and can
only run on the SICAM Q100 devices with expanded memory.

MAN_SICAM_Q100_US.book Page 222 Wednesday, June 5, 2019 9:31 AM

«
...
220
221
222
223
224
...
»

Summary of Contents for SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Reviews:

No comments