Siemens SICAM Q100 7KG95 Series Manual Download Page 204

Page: 204 / 448

9 Operation at Use of a PC

9.3 Configuration of the Device

204

SICAM Q100, 7KG95xx, Device Manual

E50417-H1040-C522-A6, Edition 06.2019

Figure 9-51

Configure Tab, Mains Signaling Voltage Input/Output Window

✧

Select the desired parameters in the list boxes and option fields as described in Table 9-18.

✧

After the parameterization, click

Send

The parameters are transmitted to the device but not enabled yet (passive set of parameters).

If you do not want to make any additional settings, continue with the

Activation

of the device configuration

according to section

Activating the Set of Parameters

. If you want to change other settings, enter the

changes and then enable the device configuration as described in section

Activating the Set of Parameters

MAN_SICAM_Q100_US.book Page 204 Wednesday, June 5, 2019 9:31 AM

Summary of Contents for SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews:

Siemens SICAM Q100 7KG95 Series, Manual, Page: 204 / 448

Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews: