Siemens SICAM Q100 7KG95 Series Manual Download Page 272

Page: 272 / 448

9 Operation at Use of a PC

9.4 Value View and Evaluation

272

SICAM Q100, 7KG95xx, Device Manual

E50417-H1040-C522-A6, Edition 06.2019

9.4.1.4 Evaluation of Modbus Slave Devices

The connection status of the up to 8 Modbus slave devices is checked and displayed as follows:

Figure 9-91

Connection status of Modbus slave devices

Connection Status

The following connection statuses are possible:

Table 9-43

Connection Status

Status

Description

good

The assigned information could be requested successfully.

no response

The Modbus slave device does not respond; communication failure or device
switched off.

no mapping data

Data mapping was not configured for the device. Therefore, data are not
requested.

excp. response

At least one request was answered with a Modbus error feedback.

msg. error

Errors in the evaluation of a response telegram (for example, CRC error)

deactivated

The Modbus slave device was not configured.

MAN_SICAM_Q100_US.book Page 272 Wednesday, June 5, 2019 9:31 AM

Summary of Contents for SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews:

Siemens SICAM Q100 7KG95 Series, Manual, Page: 272 / 448

Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews: