manualshive.com logo in svg

Siemens SICAM Q100 7KG95 Series, Manual, Page: 421 / 448

Share
Download
Siemens SICAM Q100 7KG95 Series Manual Download Page 421

16 Operating Parameters

16.6 Administrative

421

SICAM Q100, 7KG95xx, Device Manual
E50417-H1040-C522-A6, Edition 06.2019

16.6.2

Ethernet Communication

Parameter

Default Setting

Setting Range

Communication Ethernet

IP address 

1)

192.168.0.55

Any
0.0.0.0 = DHCP

Subnet mask 

1)

255.255.255.0

Any

Default gateway 

1)

192.168.0.1

Any

Ethernet switch on

no

no
yes

Enable SNMP

no

no
yes

OPC UA PubSub (MQTT)

no

no
yes

Bus protocol

Modbus TCP

-none-
Modbus TCP
IEC 61850
Both

Protocol Modbus TCP

Use a user-port number 

2)

no

no
yes

User-port number 

2)

(can only be set when 

Use a user-port 

number 

is parameterized with

 yes

)

10 000

10 000 to 65 535

Access rights for user port
(can only be set when 

Use a user-port 

number

 is parameterized with

 yes

)

Full

Full
Read only

Access rights for port 502

Full

Full
Read only

Keep Alive time

10 s

0 s = switch off
1 s to 65 535 s

Communication supervision time

600 (* 100 ms)

0 s = none
100 ms to 6 553 400 ms

Modbus TCP/RTU Gateway

(Condition: The Modbus RTU Master protocol must have been selected under serial communication.)

Activated

no

no
yes

MAN_SICAM_Q100_US.book  Page 421  Wednesday, June 5, 2019  9:31 AM

Summary of Contents for SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Reviews:

No comments