Siemens SICAM Q100 7KG95 Series Manual Download Page 353

Page: 353 / 448

10 Operation at Use of the Display

10.4 Parameterization

353

SICAM Q100, 7KG95xx, Device Manual
E50417-H1040-C522-A6, Edition 06.2019

Submenu Display Number 80.6: Communication

Figure 10-24

Submenu Display Number 80.6, Communication

80.6

Communication

87.0

IP Address

Enter

Edit

87.1

Communication
Ethernet



Enter

87.0

MAC addr.
IP addr.
Subnet
Gateway

Enter

87.1

Bus protocol:
- Modbus TCP
- IEC61850

87.2

Communication
Serial

Edit

Enter

87.2

Bus protocol:
- Modbus RTU
- Modbus Master
-None



Edit

Select parameters
acc. to following
table.

Esc

Working on
choice



Edit

Esc

Change the para -
meters acc. to
following table

Esc



87.13

Modbus TCP/
RTU gateway

Enter

87.13

Activated
Not activated

NOTE

The MAC address is shown on the display but cannot be edited.

For this purpose, a prompt is displayed which you must acknowledge with

MAN_SICAM_Q100_US.book Page 353 Wednesday, June 5, 2019 9:31 AM

Summary of Contents for SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews:

Siemens SICAM Q100 7KG95 Series, Manual, Page: 353 / 448

Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews: