Siemens SICAM Q100 7KG95 Series, Manual, Page: 236 / 448

Share

Page: 236 / 448

Siemens SICAM Q100 7KG95 Series Manual Download Page 236

9 Operation at Use of a PC

9.3 Configuration of the Device

236

SICAM Q100, 7KG95xx, Device Manual

E50417-H1040-C522-A6, Edition 06.2019

The Modbus RTU Master bus protocol must be selected both for Modbus Master and for the Modbus Gateway
function.

Additional inter-character timeout

1 ms

0 ms to 100 ms

The Modbus specification requires that
the individual characters of a serial
Modbus RTU telegram have to be
transmitted successively with a
maximum character gap of 1.5
character times (or max. 750 µs for
Baud rates >19 200 bit/s). Longer silent
intervals between the characters are
interpreted as telegram end.

A longer gap between the characters
can be tolerated with this parameter.
Note that this also causes longer cycle
times then.

If at least one SICAM P50 device is
connected to the bus, at least the
following values have to be set for

Additional character string time

:

1200 bit/s, 2400 bit/s: 0
4800 bit/s, 9600 bit/s: 2
19 200 bit/s: 3
38 400 bit/s: 4

57 600 bit/s, 115 200 bit/s: 6

Maximum 0x/1x register gap

40

0 to 200

Maximum number of

not-mapped

reg-

isters which are being requested
between mapped registers in one
request telegram.

Maximum 3x/4x register gap

10

Table 9-31

Communication Serial Settings (cont.)

Parameter

Default Setting

Setting Range

MAN_SICAM_Q100_US.book Page 236 Wednesday, June 5, 2019 9:31 AM

«
...
234
235
236
237
238
...
»

Summary of Contents for SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Reviews:

No comments