Siemens SICAM Q100 7KG95 Series Manual Download Page 218

Page: 218 / 448

9 Operation at Use of a PC

9.3 Configuration of the Device

218

SICAM Q100, 7KG95xx, Device Manual

E50417-H1040-C522-A6, Edition 06.2019

Settings Protocol Modbus

✧

Enter the desired values in the fields and select the parameters in the list boxes and in the option field as
described in Table 9-24.

Figure 9-58

Protocol Modbus

Settings Modbus TCP/RTU Gateway

To active

Modbus TCP/RTU Gateway

, proceed as follows:

✧

Select

yes

Administrative

Communication Ethernet

Modbus TCP/RTU Gateway

Activated

Figure 9-59

Modbus TCP/RTU Gateway

✧

Enter the desired values into the fields (acc. to Table 9-24).

✧

After the parameterization click

Send

After clicking

Send

, the parameters are transmitted to the device but not enabled yet (passive set of

NOTE

If you have selected

under

Use a user-port number

, you can adjust only the

Access rights for user

port 502

, the

Keep Alive time

and the

Communication supervision time

parameters.

NOTE

The Modbus TCP/RTU Gateway function requires that the Modbus RTU Master has been selected as serial
protocol in addition; see chapter 9.3.7.3.

MAN_SICAM_Q100_US.book Page 218 Wednesday, June 5, 2019 9:31 AM

Summary of Contents for SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews:

Siemens SICAM Q100 7KG95 Series, Manual, Page: 218 / 448

Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews: