Siemens SICAM Q100 7KG95 Series Manual Download Page 217

Page: 217 / 448

9 Operation at Use of a PC

9.3 Configuration of the Device

217

SICAM Q100, 7KG95xx, Device Manual
E50417-H1040-C522-A6, Edition 06.2019

9.3.7.2.1

Parameterizing the Ethernet Communication with Modbus TCP Bus Protocol

General Settings Communication Ethernet

To change the Ethernet communication settings, proceed as follows:

✧

In the navigation window, click the

Administrative

menu and then the element

Communication

Ethernet.

Select the bus protocol

Modbus TCP.

Figure 9-57

Configure Tab, Communication Ethernet via Modbus TCP Input/Output Window

✧

Enter the desired values in the fields and select the parameters in the list boxes and in the option field as
described in Table 9-24

NOTE

The enabling of SNMP via option

Enable SNMP

is only required if you want to save the SICAM Q.mib file and

use it in a MIB browser. See also section

If you do not want to make any additional settings, continue with

the Activation of the device configuration according to section Activating the Set of Parameters. If you
want to change other settings, enter the changes and then enable the device configuration as descri-
bed in section Activating the Set of Parameters.

NOTE

After changing the network settings and subsequent parameter activation the device will reset.

MAN_SICAM_Q100_US.book Page 217 Wednesday, June 5, 2019 9:31 AM

Summary of Contents for SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews:

Siemens SICAM Q100 7KG95 Series, Manual, Page: 217 / 448

Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews: