Siemens SICAM Q100 7KG95 Series Manual Download Page 374

Page: 374 / 448

13 Failures and LED Indications

13.3 Troubleshooting, Repair, and Fallback Mode

374

SICAM Q100, 7KG95xx, Device Manual

E50417-H1040-C522-A6, Edition 06.2019

13.3.2

Fallback Mode

13.3.2.1 Functional Description

The firmware of the SICAM Q100 contains a complete application for the operation of the device and runs in

2 modifications, depending on the operating state:

•

Normal operation: complete functional scope

•

Fallback mode: minimum functional scope

The fallback mode is started automatically in case of severe system errors during the device start. Once the

fallback mode is started, the indication

FALLBACK

appears on the device display.

The user interface

Fallback mode

opens in the browser. You can see and save different device information for

fault analysis in the tabs. Furthermore, you can start different maintenance functions.

Fallback Mode during Device Restart

If a severe system error occurs during a manual restart of the device, the device automatically switches to the

fallback mode.

Fallback Mode in Normal Operation

In case of an unexpected restart of the device during normal operation, the fallback mode starts only if a

severe system error occurs during the restart. Otherwise, the device switches to normal operation immediately.

Manual Start of the Fallback Mode

If necessary, you can start the fallback mode manually using the softkey F4.

13.3.2.2 Start and Maintenance of the Fallback Mode

Start of the Fallback Mode

The

Fallback Mode

is started automatically in case of severe system errors during the device start. In this case,

the user interface fallback mode with the

Information

and

Maintenance

tabs appears in the open browser

once you have entered the IP address. The

Information

tab is opened.

To start the fallback mode manually, proceed as follows:

✧

Switch off the SICAM Q100 power supply.

✧

Press the softkey F4 on the SICAM Q100 and switch on the power supply while keeping the softkey F4
pressed.

✧

Keep the softkey F4 pressed (approx. 10 s) until the display shows

FALLBACK

✧

Release the softkey F4.
SICAM Q100 starts the fallback mode.

✧

Refresh the user interface in the browser.
The user interface

Fallback mode

with the

Information

and

Maintenance

tabs opens in the open

MAN_SICAM_Q100_US.book Page 374 Wednesday, June 5, 2019 9:31 AM

Summary of Contents for SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews:

Siemens SICAM Q100 7KG95 Series, Manual, Page: 374 / 448

Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews: