Siemens SICAM Q100 7KG95 Series, Manual, Page: 208 / 448

Share

Page: 208 / 448

Siemens SICAM Q100 7KG95 Series Manual Download Page 208

9 Operation at Use of a PC

9.3 Configuration of the Device

208

SICAM Q100, 7KG95xx, Device Manual

E50417-H1040-C522-A6, Edition 06.2019

1)

According to EN 50160, up to 3 % unbalance can occur in 3-wire networks in areas with many 1-wire and

2-wire connections.

2)

The frequency “YYY” and limit “xxx” are based on the configured frequency.

Voltage event interruptions

1. Short interruption until 1 second duration
2. Short interruption until 3 minute duration
3. Long interruption longer than 3 minute duration

Any setting for user-defined
evaluation mode

Harmonic voltages

Even harmonics
Odd harmonics: multiples of 3
Odd harmonics: not multiples of 3

Any setting for user-defined
evaluation mode

Mains signaling voltages

2)

Supply voltage should be in -15.0 % to +15.0 % deviation of the
nominal/declared supply voltage

99.0 % of “YYY” Hz mains signaling voltage should be less than “xxx”
% of the nominal/declared supply voltage

Any setting for user-defined
evaluation mode

Table 9-20 Report Configuration (cont.)

NOTE

The factory settings are based on EN 50160. If you have changed the settings, the set parameters are applied
after a device restart. Resetting to the factory settings is possible.

MAN_SICAM_Q100_US.book Page 208 Wednesday, June 5, 2019 9:31 AM

«
...
206
207
208
209
210
...
»

Summary of Contents for SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Reviews:

No comments